How To Extrude Cut In Nx

In this article, we volition show you how to use Extrude command in Siemens NX. And y'all will learn the whole features of the Siemens NX Extrude control. Equally you know extrusion process is the basis of the 3D geometry creation command in general CAD software such as Siemens NX®. With the Extrude command, you can obtain the base 3D geometry. Then you tin can add other features to it.

Check: The All-time Siemens NX Books to Acquire!

How to Use Extrude Command in Siemens NX®?

Firstly, to make an extrusion in Siemens NX®, you lot demand to click on the Extrude command as the blue arrow higher up.

Secondly, subsequently opening the Siemens NX Extrude command, you lot demand to select the primary profile sketch equally blue arrow above. You tin can select the set of curves as shown in the blue box.

Past default, the vector of Extrude command in Siemens NX® is normal to the sketch surface. You can choose some other direction vector as shown by the blue arrow above for the Extrude command in Siemens NX®.

After that, in the limits department of the Siemens NX® Extrude command, you can just enter the starting offset value. If yous enter a value to the offset department of the Limits tab, the extrusion process will showtime from an offset basis from the sketch plane.

Symmetric Value Options

And and so, if yous select the Symmetric Value from the blue box, the extrusion process volition complete in two directions of the sketch plane.

Until Selected: The extrusion process will start from the selected feature from the drawing scheme.

Until Extended: The extrusion procedure starts from the selected face or aeroplane.

The same options for Commencement in Extrude control are too valid for the End option as shown past the blue box above.

So, Enter the Offset and Cease values direct every bit shown in the blue box above.

Boolean Options of Extrude in Siemens NX

You can enter the Beginning and Stop values directly from the blue box above. Besides, you can arrange the Boolean options;

None: Default option for boolean in Siemens NX® Extrude command.

Unite: If the created 3D geometry from the extrusion process intersects with other 3D geometry in the drawing scheme, you can select Unite for boolean so select the other geometry to Unite two of them in Siemens NX®.

Decrease: If the created 3D geometry from the extrusion process intersects with other 3D geometry in the cartoon scheme, you could cleave out the other 3D sketch by using the obtained extrusion 3D geometry past selecting this.

Intersect: If the created 3D geometry from the extrusion process intersects with other 3D geometry in the cartoon scheme, you tin only obtain the intersection geometry of 2 of these geometries.

You can also enter a draft angle as From Showtime Limit. You just enter an angle value to obtain geometries every bit the red arrow above. As well, if you have a place or section within the obtained geometry, you tin can select From section from the blood-red box to a higher place. And commencement your drafting angle from this section inside the Extruded geometry.

You can enter an offset value to obtain geometries as shown by the cherry pointer above. We need to enter the showtime start and end values in Siemens NX®. We can as well obtain Offset structures as Two-Sided, Single-Sided, or Symmetric from the cerise box option above.

If y'all want to obtain a sheet structure as shown by the blood-red pointer above from Extrude command in Siemens NX®, y'all need to adapt the Trunk Blazon option from Solid to Sheet as shown past the red box in a higher place. When you lot are done with the call options of Extrude command-click on OK or Apply to complete in Siemens NX®.

Decision

The use of the Extrude command in Siemens NX is very simple like this.

Practice not forget to get out your comments and questions beneath virtually the Extrude control in Siemens NX®!

NOTE: We apply all the screenshots and images for educational and informative purposes. Images used courtesy of Siemens NX®.

Above all, Siemens NX has lots of useful commands and features. Y'all can check them below;

Drawing Polygons Effectively in Siemens NX Sketching

Resizing Lots of Sketch Entities at Same Time in Siemens NX

Trimming Quickly Siemens NX Sketching Objects

Create Chamfers Effectively in Siemens NX Sketching

Drawing Circles Finer in Siemens NX Sketching

Source: https://mechanicalland.com/extrude-command-in-siemens-nx/

Share this post